Esp8266 digital clock OLED display

Clock3-How to use
7月 10, 2022
10月 23, 2022
Show all

Esp8266 digital clock OLED display

This is a wifi clock .The clock use ds3231 as clock chip, precision is about 2ppm,that means it’s maximum error is about 1 minute per year.It can connect your home wifi through the esp8266 wifi chip .With some simple settings, you can control this clock over the network.It have a funny alarm, you can choose the alarm mode, whether it will keep ringing until you turn it off or only for a minute

Follow our step, you can make a cool network clock yourself

HOW to USE?Vedio

Now let’s start making this alarm clock

Welding Principles
Components are soldered from low to high

first solder the resistor and capacitor, this is 0805 SMD

Look at the picture, Solder the components to the corresponding positions on the picture

10K*3 and 1K*1

the back of the pcb

10K*1 and 1K*2

Next Solder the capacitor

PCB back

Welding power chip,LM1117

this chip can change 5v to 3.3v for the chip working

Welding power indicator led

LEDs have positive and negative poles
The green dot is the negative pole, the negative pad is soldered to the right side

Clock chip,ds3231

You need to learn to solder the smd , it’s not very difficult

This is the alarm clock chip, which stores audio files

This is used as led driver

This is the clock chip battery holder
For power failure time memory
(battery type is cr1220,you can by yourself)

This is the wifi chip which is used for network communication and for controlling the entire clock

Well, at this step, the main circuit board has been soldered
Let’s make a 1s interval running water lamp

This uses a dedicated chip, 1s interval, can drive 6 leds

A few points to note

  1. The direction of the chip, pay attention to the position of the red dot on the picture
  2. The positive and negative poles of the led, the outside of the circle is the negative pole, the inside is the positive pole, all leds are

Drill a hole in the middle of the plank, the wire needs to go through this hole

A spacer needs to be added between the pcb and the board, what you receive is a white plastic spacer

The positive and negative wires of the led pcb are welded to this position of the main pcb, as shown in the picture

copper pillar,Installed on the four corners

OLED display

4 wires, 2 power wires, 2 signal wires
Welding as shown

speaker, soldered to the “beep” labeled pads on the pcb
This does not distinguish positive and negative

Then glue on the sides

The oled screen is also glued to the front

Finally, this transparent glass cover can be directly covere on it

Next is how to set and use this alarm Clock

First of all, you need a mobile phone charger, it can be powered by connecting to the type-c charging cable.
then configure wifi
phone – settings – wifi
Find the wifi hotspot “AutoconnectAP”, which is generated by the clock itself
To enter this AP, a password may be required, and the password is “password
Then select the wifi of your home, enter the password of your home wifi, and click save
Wait a while, it may take 30 seconds, until the page disappears, then the oled screen of the clock will show the assigned ip address
Use this address, enter the address in the browser, you can set the clock(The vedio below is another type clock,but it is the same way to set the clock)

5 评论

  1. admin说道:

    solder to c1

  2. Ameen Ghannam说道:

    Hello: I built the Esp8266 digital clock OLED display: But there is a problem with the clock not showing the time. Please view the attached video file:

    1) The clock turns on and connect to my Wifi Network, (Good)!
    2) It then Identifies with the correct IP address (Good)!

    3) When the clock display comes on, it shows incorrect numbers/letters on the screen?? (BAD!). (see attached photo) These numbers do not change. (Note I did set the time via the Web interface and it says setting successful!

    Can you inform me how to correct this problem, or send me the replacement board? I purchased this item from you on

  3. Ameen Ghannam说道:

    Hello, I am building the Esp8266 digital clock OLED display, which I purchased from Etsy.

    For the building of the 1s interval running water lamp (the 6 LED Lights section on the top of the clock), My parts bag included this small component (a capacitor I think?) . (You can see it next to LED light section in the photo I have attached) . Do I require this part. I do not see in the instructions where I would solder this to the circuit board? Thank you


您的电子邮箱地址不会被公开。 logo